![]() ![]() The question that I'm gonna throw here is that: I noticed the max file descriptor setup in the zone is 256 as the default value, which then Splunk recommend to increase to ~ $ ulimit -n I have raised a case to Splunk, Splunk support investigated the Splunk diag output uploaded and responded that these seemed external rather than splunk triggered restarts. Please wait, as this may take a few minutes. Validated: _audit _blocksignature _internal _thefishbucket firedalerts history main os summaryĬhecking filesystem compatibility. In /var/svc/log/application-splunk-forwarder:default.log message snippets like below can be seen:Ĭhecking mgmt port : Checking configuration. Recently I noticed this SMF service has had quite some restarts, which I believe no user or cronjob action is responsible for. Online 11:45:27 svc:/application/splunk/forwarder:default Where a Splunk agent aka Splunk forwarder is svcs forwarder SunOS spresapp011 5.10 Generic_150400-48 sun4u sparc SUNW,SPARC-Enterprise Rpm -i splunkforwarder-linux-2.6-x86_64.I have a Solaris 10 zone running on a M4000. You could also use the deb and RPM packages but I wouldn’t bother with them. The config commands above will modify these files. ![]() $SPLUNK_HOME/etc/apps/SplunkUniversalForwarder/default Two versions of the default config file, don’t use these: $SPLUNK_HOME/etc/system/default Make sure to restart the forwarder after adding data sources. You will want to make sure that the splunk user has read access to the logs. Splunk add monitor /var/log -sourcetype journald -index my-test-index2 Splunk add monitor /var/log -sourcetype linux_logs -index main Splunk add monitor /var/log/nginx -sourcetype nginx -index my_nginx These are some examples of data sources that you could add. Splunk add forward-server splunk1:9997 -auth admin:password1 Also swap in which ever password you had setup. Specify the Splunk index server to coneect to here. If you are using a dedicated user, make sure you are logged in as that user while setting up data sources. You can now start and stop it with systemd like this: Systemctl list-unit-files | grep -i splunk Now you will see it listed with this command: Sudo /opt/splunkforwarder/bin/splunk enable boot-start -systemd-managed 1 Run this while still logged in as the dedicated splunk user. It will also ask you to create a user and password to manage the forwarder.Įnable Splunk start on boot with systemd. Setup the SPLUNK_HOME and PATH environment variables for the current shell while also adding it to your bashrc file to make it persistent.Įcho export SPLUNK_HOME=/opt/splunkforwarder > ~/.bashrcĮcho export PATH=$PATH:$SPLUNK_HOME/bin > ~/.bashrcįor the first time starting, start the forwarder like this to accept the license without reading it. You will want to make sure that you are logged in as this user before starting for the first time and before enabling in systemd. You can also do this from the CLI if you want.Īssuming that you run splunk as the dedicated user “splunk” you will want become that user first.īecome the splunk user. Restart Splunk from the CLI on the Splunk indexer host ( where you installed Splunk Enterprise ): If already setup, you will see the port listed as “Enabled” here.This can be done from the GUI with the following steps. You need to enable receiving before you can actually receive data from your forwarders. ![]() NOTE - You should just swap in your own specific information In any place where we use an exact version number, IP address, or home directory path. We’re covering the following on this page: Before actually setting up the forwarder we are going to show you how to enable receiving on the indexer so that it will have something to connect to. This will allow you to send logs and data from a remote host to a centralized indexer. We’re going to show you how to setup the Splunk Universal Forwarder. Splunk Universal Forwarder Install and Setup ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |